Updated November 2026
RV solar panels from Zamp are a practical way to keep your house batteries charged while camping off-grid. This guide walks you through matching a Zamp setup to your power needs, checking your roof and wiring, and mounting the panels so they perform well and stay put. By the end, you will know which questions to answer before you buy and what to do once the kit arrives.
Step 1: Work Out Your Daily Power Needs
Start with your loads. List the appliances you use, their wattage, and how many hours per day you run them. Multiply watts by hours to get watt-hours per day. A small fridge, LED lights, water pump and phone charging might add up to a few hundred watt-hours on a typical day, while a microwave or coffee maker can push that much higher in a short burst.
Shopping for one? See our guide: 5 Best RV Solar Panel Install Mounting Kits for Roof Mounting (2026).
Next, compare that number with your battery capacity. Lead-acid batteries should not be drained much below about half their rated capacity, while lithium batteries tolerate deeper discharge. Your panels need to replace what you use, plus some margin for cloudy days.
Step 2: Choose the Right Zamp Panel Setup
Zamp sells panel kits and mounting hardware for different roof sizes and power goals. When you compare options, focus on three things: total wattage, panel size, and whether the kit includes a charge controller. A kit with a controller saves you from sourcing one separately and helps make sure the panels charge your batteries correctly.
Measure your usable roof area before you order. Check for air conditioner units, vents, skylights and ladder rails. Panels need clear space and must not block airflow or hatches. Many owners find that a few mid-size panels fit better on a typical camper roof than one large array.
Step 3: Plan the Mounting and Wiring
Mounting method depends on your roof. Many RV roofs are fiberglass or rubber membrane, and manufacturers usually recommend specific adhesives, sealants or mounting feet for each type. Follow the instructions for your roof material and use sealant rated for it. Drill holes only where the instructions say to, and seal every penetration carefully to prevent leaks.
Run cable through the roof with proper grommets and keep wire runs short to limit voltage drop. Size the wire to the current the kit specifies. If you are not comfortable with roof work or 12-volt wiring, have an RV technician handle the installation. Consult a professional for any work involving electrical systems or roof penetrations.
Common Mistakes to Avoid
- Buying panels based on total wattage alone without checking whether your roof has enough clear space.
- Skipping the charge controller or using one that does not match your battery chemistry.
- Using the wrong sealant, which can lead to slow leaks you may not notice for months.
- Running undersized wire, which wastes power and can overheat connections.
- Ignoring shade from roof fixtures, which can cut output more than expected.
Recommended Gear
- Zamp Solar Panel Kit: A complete starting point for many RV owners, since it bundles panels, mounting hardware and controller compatibility. View on Amazon
- RV roof sealant: Choose a sealant rated for your roof material, since it protects the mounting holes from water entry. View on Amazon
- Multimeter: A simple tool for checking panel voltage and confirming wiring before you connect everything to the batteries. View on Amazon
Related Reading
If you are still deciding between approaches, read Solar Panels RV Installation: 5 Best Mounting Kits and Panels (2026) for kit comparisons. For a walkthrough of the physical install, see Mounting Solar Panel on RV: A Step-by-Step Guide for Beginners. To size your array against your battery, How Many Watt Solar Panel to Maintain RV Battery? A Practical Answer is a useful companion. Owners comparing brand-specific systems may also find Renogy RV Solar Panels: How to Choose and Install the Right Kit helpful.
FAQ
Are Zamp solar panels good for RV use?
Zamp panels are designed for RV roofs and are widely used by owners who want a plug-in style setup with matching mounts. Their suitability depends on your power needs and roof space, so check the specifications against your load calculation.
How many panels do I need for my RV?
It depends on your daily watt-hour use and how much sun you get. Calculate your daily consumption first, then choose a total wattage that replaces it with a margin for weather.
Can I install Zamp panels myself?
Many owners with basic tools and electrical experience do the work themselves, following the manufacturer’s instructions closely. If you are unsure about roof sealing or wiring, consult a qualified RV technician.
Conclusion
A well-chosen Zamp setup starts with an honest look at your power use, your roof space and your battery type. Match the kit to those numbers, follow the mounting and sealing instructions for your roof, and wire it with the right gauge and controller. Done carefully, your panels will keep your batteries topped up through much of your camping season.
